Header Image

Redesigh website

Missile LXQ Series - LXQR4000 IR340A Shank

Missile LXQ IR340A diagram

Features:
  • Easy to service
  • Special heat-treated alloy piston for long life, Rockwell hardness 60
  • Minimum loss of performance when injecting foam or water

Item # Description Part #
1 Back Head LQ4001
2 Back Head O-Ring LQ4002
3 Choke  
4 Air Check Valve LQ4004
5 Air Check Valve Spring LQ4005
6 Make-Up Rubber (Buffering) LQ4006
7 Air Distributor LQ4007
8 Air Distributor O-Ring LQ4008
9 Cylinder LQ4009
10 Wear Sleeve LQ4010
11 Piston LQR4011
12 Piston Stop Ring LQR4012
13 Bit Retaining O-Ring LQR4013
14 Bit Retaining Ring LQR4014
15 Chuck (Drive Sub) LQR4015
  Choke Plug Kit LQ4029
  O-Ring Kit LQ4030

Specifications


Length (w/o drill bit) 39.2"
Outside Diameter 3.81"
Weight (w/o bit) 84.6 lbs.
Cylinder Bore 3.071"
Piston O.D. 3.067"
Piston Stroke 3.93"
Piston Weight 18.9 lbs.
Hole Sizes 4 1/8" - 5"
Air Pressure Consumption 100 psi - 350 psi
Wrench Size A/F 3.149"
Connection Std. 2 7/8" API Reg Pin

Air Consumption Chart


PSI 150 200 250 300 350 400
CFM with blank choke 240 340 440 540 - -
with 1/8" choke 375 595 760 925 1,060 1,205
with 1/4" choke 425 665 845 1,095 1,270 1,350

All Hammers come Fitted with blank Choke located in the Air Check Valve




Hammer Service Log


Wear Sleeve / Piston Clearance

Part New Dimension Discard Clearance
Wear Sleeve A 3.071" greater than or equal to 0.010"
Piston OD B 3.067"
Wear Sleeve / Piston Clearance diagram

Inner Cylinder / Piston Clearance

Part New Dimension Discard Clearance
Cylinder ID C 2.441" greater than or equal to 0.010"
Piston OD D 2.437"
Inner Cylinder / Piston Clearance diagram

Distributor Probe / Piston ID Clearance

Part New Dimension Discard Clearance
Distributor Probe OD F 1.019" greater than or equal to 0.010"
Piston ID E 1.024"
Distributor Probe / Piston ID Clearance diagram

External Wear

Description Wear Limit
Wear Sleeve Discard Dimension 3.425"
NOTE:
Chuck should be replaced when wear transfers to wear sleeve.


Lubrication

G-Force Series Hammers are precision-made tools and should be treated as such. Only the highest quality lubrication should be used and a constant flow of oil must be maintained at all times. Recommended lubrication amount 1/3 Pint per 100 cfm per hour.

Recommended Grades of Lubricant

ESSO
MATEX
CASTROL
SHELL
MOBILE
AROX EP 150
RDO 302
RD OIL DP 100
AIR TOOL OIL 2 A 320
ALMO NO. 5
Heavy duty oil is recommended for all year-round use, in particular where air supply to the hammer is at high temperature. If lighter grade oil is required due to very low ambient temperatures, amount of oil being used should be increased by 30 percent.

Recommended Pull Down

Minimum @ 100 psi - 500 lbs. Maximum @ 350 psi - 1800 lbs.

Missile Warranty will be voided by the following:


Welding on Wear Sleeve.
Heating Case with a Torch.
Gripping Wrenches across Threads.
Hammering on Casing.

READ WARNING LABEL ATTACHED TO HAMMER.