Header Image

Redesigh website

Missile LXQ Series - LXQR3000 IR3.5 Shank

Missile LXQ IR3.5 diagram

Features:
  • Easy to service
  • Special heat-treated alloy piston for long life, Rockwell hardness 60
  • Minimum loss of performance when injecting foam or water

Item # Description Part #
1 Back Head LQ3001
2 Back Head O-Ring LQ3002
3 Choke  
4 Air Check Valve LQ3004
5 Air Check Valve Spring LQ3005
6 Air Check Valve Guide LQ3006
7 Make-Up Rubber (Buffering) LQ3007
8 Center Tube LQ3008
9 Center Tube Stop Ring LQ3009
10 Wear Sleeve LQ3010
11 Piston LQ3011
12 Piston Stop Ring LQ3012
13 Bit Retaining O-Ring LQ3013
14 Bit Retaining Ring LQ3014
15 Chuck LQ3015
  Choke Plug Kit LQ3029
  O-Ring Kit LQ3030

Specifications


Length (w/o drill bit) 38.07"
Outside Diameter 3.14"
Weight (w/o bit) 48.4 lbs.
Cylinder Bore 2.559"
Piston O.D. 2.555"
Piston Stroke 3.54"
Piston Weight 9.7 lbs.
Hole Sizes 3 3/8" - 5"
Air Pressure Consumption 100 psi - 350 psi
Wrench Size A/F 2.559"
Connection Std. 2 3/8" API Reg Pin

Air Consumption Chart


PSI 100 150 200 250 300 350 400
CFM with blank choke 110 180 250 330 415 505 605
with 1/8" choke - - - - - - -
with 1/4" choke - - - - - - -

All Hammers come Fitted with blank Choke located in the Air Check Valve




Hammer Service Log


Wear Sleeve / Piston Clearance

Part New Dimension Discard Clearance
Wear Sleeve A 2.559" greater than or equal to 0.010"
Piston OD B 2.555"
Wear Sleeve / Piston Clearance diagram

Inner Cylinder / Piston Clearance

Part New Dimension Discard Clearance
Cylinder Tube OD C 2.558" greater than or equal to 0.010"
Center Tube MD D 1.846"
Piston MD E 1.851"  
Inner Cylinder / Piston Clearance diagram

Distributor Probe / Piston ID Clearance

Part New Dimension Discard Clearance
Center Tube Probe OD G 0.960" greater than or equal to 0.010"
Piston ID F 0.965"
Distributor Probe / Piston ID Clearance diagram

External Wear

Description Wear Limit
Wear Sleeve Discard Dimension 2.952"
NOTE:
Chuck should be replaced when wear transfers to wear sleeve.


Lubrication

G-Force Series Hammers are precision-made tools and should be treated as such. Only the highest quality lubrication should be used and a constant flow of oil must be maintained at all times. Recommended lubrication amount 1/3 Pint per 100 cfm per hour.

Recommended Grades of Lubricant

ESSO
MATEX
CASTROL
SHELL
MOBILE
AROX EP 150
RDO 302
RD OIL DP 100
AIR TOOL OIL 2 A 320
ALMO NO. 5
Heavy duty oil is recommended for all year-round use, in particular where air supply to the hammer is at high temperature. If lighter grade oil is required due to very low ambient temperatures, amount of oil being used should be increased by 30 percent.

Recommended Pull Down

Minimum @ 100 psi - 500 lbs. Maximum @ 350 psi - 1800 lbs.

Missile Warranty will be voided by the following:


Welding on Wear Sleeve.
Heating Case with a Torch.
Gripping Wrenches across Threads.
Hammering on Casing.

READ WARNING LABEL ATTACHED TO HAMMER.