Header Image

Redesigh website

Missile LXQ Series - LXQM12000 SD12 Shank

Missile LXQ SD12 diagram

Features:
  • Easy to service
  • Special heat-treated alloy piston for long life, Rockwell hardness 60
  • Minimum loss of performance when injecting foam or water

Item # Description Part #
1 Back Head LQ1201
2 Back Head O-Ring LQ1202
3 Back Head Washer LQ1203
4 Choke  
5 Air Check Valve LQ1205
6 Air Check Valve Spring LQ1206
7 Make-Up Rubber (Buffering) LQ1207
8 Air Guide LQ1208
9 Air Distributor LQ1209
10 Air Distributor O-Ring LQ1210
11 Cylinder LQ1211
12 Cylinder Stop Ring LQ1212
13 Wear Sleeve LQ1213
14 Piston LQ1214
15 Piston Stop Ring LQ1215
16 Bit Retaining O-Ring LQ1216
17 Bit Retaining Ring LQ1217
18 Guide Sleeve LQ1218
19 Chuck Washer LQ1219
20 Chuck LQ1220
21 Drive Pin LQ1221
  Choke Plug Kit LQ1229
  O-Ring Kit LQ1230

Specifications


Length (w/o drill bit) 75.11"
Outside Diameter 10.79"
Weight (w/o bit) 1,373 lbs.
Cylinder Bore 8.5"
Piston O.D. 8.494"
Piston Stroke 4.13"
Piston Weight 256.5 lbs.
Hole Sizes 12" - 17 1/2"
Air Pressure Consumption 100 psi - 250 psi
Wrench Size -
Connection Std. 6 5/8" API Reg Pin

Air Consumption Chart


PSI 100 150 200 250 300 350
CFM with blank choke 750 1,125 1,675 1,925 2,475 2,960
with 1/8" choke 825 1,225 1,800 2,150 - -
with 1/4" choke 900 1,325 1,925 2,275 - -

All Hammers come Fitted with blank Choke located in the Air Check Valve




Hammer Service Log


Wear Sleeve / Piston Clearance

Part New Dimension Discard Clearance
Wear Sleeve A 8.5" greater than or equal to 0.010"
Piston OD B 8.494"
Wear Sleeve / Piston Clearance diagram

Inner Cylinder / Piston Clearance

Part New Dimension Discard Clearance
Cylinder ID C 7.008" greater than or equal to 0.010"
Piston OD D 7.001"
Inner Cylinder / Piston Clearance diagram

Distributor Probe / Piston ID Clearance

Part New Dimension Discard Clearance
Distributor Probe OD F 2.244" greater than or equal to 0.010"
Piston ID E 2.236"
Distributor Probe / Piston ID Clearance diagram

External Wear

Description Wear Limit
Wear Sleeve Discard Dimension 10"
NOTE:
Chuck should be replaced when wear transfers to wear sleeve.


Lubrication

G-Force Series Hammers are precision-made tools and should be treated as such. Only the highest quality lubrication should be used and a constant flow of oil must be maintained at all times. Recommended lubrication amount 1/3 Pint per 100 cfm per hour.

Recommended Grades of Lubricant

ESSO
MATEX
CASTROL
SHELL
MOBILE
AROX EP 150
RDO 302
RD OIL DP 100
AIR TOOL OIL 2 A 320
ALMO NO. 5
Heavy duty oil is recommended for all year-round use, in particular where air supply to the hammer is at high temperature. If lighter grade oil is required due to very low ambient temperatures, amount of oil being used should be increased by 30 percent.

Recommended Pull Down

Minimum @ 100 psi - 5600 lbs. Maximum @ 350 psi - 9900 lbs.

Missile Warranty will be voided by the following:


Welding on Wear Sleeve.
Heating Case with a Torch.
Gripping Wrenches across Threads.
Hammering on Casing.

READ WARNING LABEL ATTACHED TO HAMMER.